Skip to content
Operations

Excavation Slope Angle by Soil Type: How Far Back to Cut the Sides

November 11, 202610 min read
In this article

A 3 m deep trench for a sewer line, 2 m wide at the bottom, is dug with vertical sides in sandy ground because the plot is narrow and the pipe crew is due the next morning. Overnight the top of one side dries out and a section slides in. Nobody is in the trench, so the cost is one day and a re-dig. With the crew inside, it would have been a very different story: a cubic metre of soil weighs well over a tonne.

The excavation slope angle by soil type is what decides whether the sides stand. It also decides how wide the dig is at ground level, how much extra soil comes out, and whether the job fits on the plot at all. That makes it an equipment and planning question as much as a safety one, and it should be answered before the excavator is booked.

This guide uses the US excavation rule, OSHA 29 CFR 1926 Subpart P, because it publishes a clear table of slopes by soil type. It is a US reference, not Egyptian law. On an Egyptian project the soil report, the consultant and the project specification come first; the table is a way to understand what they are asking for and to sanity-check a plan.

When the sides need protecting at all

Under OSHA 1926.652, everyone working in an excavation must be protected from cave-ins by a protective system, with two exceptions:

  • the excavation is made entirely in stable rock, or
  • it is less than 5 feet (1.52 m) deep and a competent person has examined the ground and found no indication of a potential cave-in.

Note the second condition. A shallow trench is not automatically safe; someone competent still has to look at it.

A protective system is one of three things: sloping the sides back, benching them in steps, or supporting them with shoring or a trench shield. This article is mainly about the first two, and about when they stop being practical.

The slope table

Appendix B of the rule gives the maximum allowable slope for each soil type, for excavations less than 20 feet (about 6.1 m) deep. Slopes are written horizontal to vertical (H:V): 1½:1 means the side goes back 1.5 m for every 1 m of depth.

Soil typeMaximum slope (H:V)Angle from horizontalSet-back per 1 m of depth
Stable rockVertical90°0
Type A¾:153°0.75 m
Type B1:145°1.0 m
Type C1½:134°1.5 m

Four points from the same appendix matter as much as the table:

  1. Deeper than 20 feet, sloping or benching must be designed by a registered professional engineer. The table stops there.
  2. No classification, no table. If nobody has classified the soil, the rule's default is the flattest slope: 1½:1, 34°.
  3. Signs of distress such as cracks near the edge, the edge subsiding, material spalling from the face or the bottom heaving mean the slope must be cut back further, by at least another ½:1.
  4. Loads near the edge, including stored material, spoil, machines and traffic, mean a competent person must decide how much flatter the slope has to be.

There is also a short-term allowance for Type A soil only: ½:1 (63°) where the excavation is open 24 hours or less and is 12 feet (about 3.7 m) deep or less.

Which soil type do you have

Appendix A sorts soil into three types, from most stable to least. In short:

  • Type A: cohesive soil with an unconfined compressive strength of 144 kPa or more, such as clay, silty clay and sandy clay, and cemented soils such as hardpan.
  • Type B: cohesive soil between 48 and 144 kPa, angular gravel, silt and sandy loam, and previously disturbed soil that is not Type C.
  • Type C: cohesive soil at 48 kPa or less, gravel, sand and loamy sand, and any soil that is submerged or has water freely seeping from it.

The disqualifiers are where sites go wrong. No soil is Type A if it is fissured, if it is subject to vibration from heavy traffic, piling or similar, or if it has been previously disturbed. In a layered deposit, the whole face is classified by its weakest layer. And if conditions change after classification, for example after rain, the soil has to be evaluated again.

The classification has to be made by a competent person, using at least one visual and one manual test. The visual part is looking at the soil as it comes out and at the open face: does it stay in clumps or run, are there cracks, is water seeping, are there signs of old trenches or fill. The appendix also describes manual tests such as rolling a moist sample into a thin thread to check for cohesion.

For Egyptian sites, three practical readings follow from those definitions:

  • Sand is Type C. Much of the ground in the new cities and desert sites is sandy. Under this classification that means 34°, however firm the face looks on the first morning.
  • Fill and old trenches are disturbed soil. Ground beside existing utilities, old foundations or backfilled plots cannot be Type A.
  • Seeping water means Type C. Where groundwater is close to the surface, a clay that would otherwise classify better drops to the flattest slope once water comes out of the face.

What the slope does to the size of the dig

The arithmetic is simple, and it is the part that changes the equipment plan:

top width = bottom width + 2 × depth × H

Take the trench from the opening: 3 m deep, 2 m wide at the bottom.

SidesSet-back each sideTop widthCross-sectionVolume per 10 m of trench
Vertical (supported)02.0 m6.0 m²60 m³
Type A, ¾:12.25 m6.5 m12.75 m²127.5 m³
Type B, 1:13.0 m8.0 m15.0 m²150 m³
Type C, 1½:14.5 m11.0 m19.5 m²195 m³

In sand, the sloped trench is 11 m wide at the top and moves more than three times the soil of a supported vertical trench. Those are bank cubic metres; the soil swells once dug, so the truck count grows faster still. Every extra cubic metre also has to be brought back and compacted as backfill.

So before choosing, work out both versions. The method for turning cubic metres into machine hours and trucks is in excavator production per hour.

Benching

Benching cuts the sides in steps instead of a plane. Under Appendix B it is allowed in Type A and Type B soil, within the same overall slope and with limits on the bench dimensions. The appendix shows no benched configuration for Type C soil.

In Type B and Type C soil, the appendix also requires that any vertical-sided lower portion be shielded or supported to at least 18 inches (about 0.46 m) above the top of the vertical part. The common habit of sloping the top and leaving the bottom metre vertical and unsupported is not what the table allows in those soils.

Slope or support: how to choose

Slope the sides when:

  • there is room at ground level for the top width plus a clear strip for spoil and machines,
  • the excavation is shallow enough that the extra volume is modest, and
  • the soil report or the competent person's classification supports the slope.

Support the sides when:

  • the plot is tight. On an infill plot between existing buildings, a 4.5 m set-back per side does not exist.
  • there are buildings or walls alongside. The rule requires shoring, bracing or underpinning where an excavation endangers adjoining structures, and digging below the base of a neighbouring footing needs a support system or an engineer's approval.
  • the dig is deep. Volume grows with the square of depth on the sloped parts, and past 20 feet the slope needs an engineer's design in any case.
  • there is water. Dewatering and support are usually designed together.

Support systems are engineered items: either designed by an engineer or used strictly within the manufacturer's tabulated data. Improvised timber is not a system. How this fits into the sequence of a basement or footing job is covered in foundation excavation in Egypt.

Rules at the edge

The slope only works if the edge is managed. From OSHA 1926.651:

  • Spoil and equipment stay at least 2 feet (0.61 m) back from the edge, or are held by retaining devices. Further is better, and the excavator and the trucks are a load on the slope too.
  • A way out. Trenches 4 feet (1.22 m) deep or more need a ladder, stair or ramp placed so that nobody has to travel more than 25 feet (7.62 m) sideways to reach it.
  • Machines near the edge. Where an operator cannot see the edge clearly, use barricades, a signaller or stop logs.
  • Water. Nobody works in an excavation where water is accumulating unless precautions are in place, and surface water is diverted away from the edge.
  • Daily inspection. A competent person inspects the excavation and the area around it before work starts, as needed during the shift, and after every rainstorm.
  • Buried services are located before digging, as the UK HSE's excavation guidance also sets out. For small utility trenches, see mini excavator for villa foundations and utility trenches.

What to settle before you book the machine

  1. Depth, bottom width and length of the dig, from the drawings.
  2. Soil type and groundwater level, from the soil report or a competent person's classification.
  3. Slope or support, decided by the engineer, with the top width drawn on the site plan.
  4. Volume to dig and volume to backfill, for the chosen option.
  5. Where spoil goes and where the excavator and trucks stand, clear of the edge.
  6. Who inspects the excavation each morning and after rain.

The top width also affects machine choice: a wider sloped dig may need a longer reach or a second position, while a narrow supported trench may suit a smaller machine.

Quick summary

  1. Under the OSHA rule, sides need protection from 1.52 m deep, and below that only if a competent person finds no sign of a cave-in.
  2. Maximum slopes: Type A 53°, Type B 45°, Type C 34°. Unclassified soil takes 34°.
  3. Sand, seeping water and disturbed ground push the classification down.
  4. Top width = bottom width + 2 × depth × H. In sand at 3 m deep, that adds 9 m.
  5. When the plot, the neighbours, the depth or the water rule out a slope, support the sides with an engineered system.
  6. Keep spoil and machines back, give a way out, and inspect every day and after rain.

Next step

With the depth, soil type and top width in hand, browse excavator rental to compare sizes and request a quote, or message us on WhatsApp with the dig dimensions and the soil report.

Sources and scope

Each source supports the topic described below, not every statement in this article. Foreign guidance does not replace Egyptian requirements or site rules. Use the manual matching the machine model and serial number for operation.

  • OSHA 29 CFR 1926 Subpart P, Appendix B — Sloping and benching

    Table B-1 maximum allowable slopes for excavations less than 20 ft deep (Type A ¾:1, Type B 1:1, Type C 1½:1), the short-term Type A allowance, flattening the slope on signs of distress or surcharge loads, and the permitted benching configurations. US excavation rule, not Egyptian law.

  • OSHA 29 CFR 1926 Subpart P, Appendix A — Soil classification

    Definitions of stable rock and Type A, B and C soil, the conditions that rule out Type A (fissures, vibration, previous disturbance), classification by the weakest layer, and the visual and manual tests a competent person uses. US excavation rule, not Egyptian law.

  • OSHA 29 CFR 1926.652 — Requirements for protective systems (excavations)

    Cave-in protection is required except in stable rock or below 5 ft (1.52 m) where a competent person finds no indication of a potential cave-in; the default slope without soil classification is 1½H:1V (34°); support and shield systems follow an engineer's design or the manufacturer's tabulated data. US excavation rule, not Egyptian law.

  • OSHA 29 CFR 1926.651 — Specific excavation requirements

    Locating underground installations, egress from trenches 4 ft (1.22 m) or deeper within 25 ft (7.62 m) of travel, spoil and equipment at least 2 ft (0.61 m) from the edge, warning systems for mobile equipment, water, adjacent structures and daily inspections by a competent person. US excavation rule, not Egyptian law.

  • HSE — Excavations

    Collapse prevention, edge protection, buried services, water and inspection. UK guidance, not Egyptian law.

Need a machine for your site?

Browse EXON's maintained fleet or talk to the team for a project quote.

Keep reading